recent

Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner

Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner
Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner
Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner
Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner
Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner
Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner
Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner
Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner

Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner
You may also like. Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner N. HF QRP Transceiver, put battery 12v and ANT can qso. DC IN:9-13V Max:3A. Output POWER:<=10W. Transmit: 160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive: 3.5-30 MHz nominal including general coverage, 0.8-32 MHz at reduced. Bandwidth:300Hz-10Khz Adj. SWR:Display 1-5. Better than -108 dBm (0.89uV) in a 2.3 kHz bandwidth. Better than -120 dBm (0.22uV) in a 300 Hz bandwidth. Enclosure Design: Removable. STM32f407VGT6 1M memory. Because this is a software-defined radio and due to ongoing modifications/improvements of the software and hardware, the specifications continue to improve. Receiver sensitivity for 10dB S/N, CCITT filtering, taken at 28.3 MHz. Frequency Translation enabled. Better than -111 dBm (0.6uV) in a 2.3 kHz bandwidth. Better than -126 dBm (0.11uV) in a 300 Hz bandwidth. The above specifications are for a receiver on which the published sensitivity modifications are performed. Receive: 3.5-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. The ability of the Si570 to tune the radio below 2.5 MHz is not guaranteed in its specifications, but most units have enough range to tune just below 1.8 Mhz. Maybe there are some small gaps where LO does not work-if it works, it works fine. Indicator is the color of the frequency digits. White: fully working. Yellow: mostly working, maybe there are some small gaps. Red: not working. Spectrum Scope: This is a spectrum analyzer with the vertical divisions representing userdefinable amplitude variations of 5,7.5,10, 15,20,1 S-Unit (6dB), 2 S-Units (12dB) or 3 S-Units. The baseline ("reference level") of the analyzer is automatically adjusted so that the signals within the displayed passband best fit the dynamic range selected by the userselected dB/division. A graticule along the bottom of the display indicates the approximate frequency of the signal being displayed over a width of +/- 24 kHz. Waterfall Display: As with the spectrum scope, the frequency is displayed along the "x" axis but the signal strength is implied by the displayed color. The newest signals are displayed along the bottom of the screen, but as new readings arrive, the representations of the older signals are shifted upwards giving an ephemeral time record of recent activity on nearby frequencies. There are several options for color "palettes" that range from simple grayscale to "cold-hot" to "rainbow" to represent weak to strong signals. There is also a "Magnify" mode for both the Spectrum Scope and Waterfall Display mode that provides 2x magnification, reducing the visible spectral width to just +/- 12 kHz 24 kHz total. Both the Spectrum Scope and Waterfall Display are very highly configurable. It is possible to disable one or both spectral display modes if desired. Transmitter power output: <=10 Watts, typical, linear. Modifications may be made to increase this: Follow the discussions in the Yahoo group. Frequency stability: +/- 30 Hz at 14 MHz over the range of 10 to 35 C, ambient with the transceiver in the case or better with the TCXO active. It can be much better than this. FM options: Carrier (ultrasonic) squelch, subaudible tone encoding and decoding, tone burst ("whistle up") generation, "narrow" (+/-2.5 kHz) and "wide" (+/-5 kHz) deviation and the selection of 7.2,10,12 or 15 kHz pre-detection receive bandwidths. FM sensitivity for 12 dB SINAD, CCITT filtering. 7.2 kHz BW filter: -103.7 dBm (1.46uV) with 1 kHz tone at +/-1.5 kHz. 10 kHz BW filter: -102.1 dBm (1.75uV) with 1 kHz tone at +/-1.5 kHz. 10 kHz BW filter: -104.0 dBm (1.41uV) with 1 kHz tone at +/. Please well connect correct power supply and antenna before switching on for use. Improper power supply and antenna connection may damage the transceiver. Please leave note for your special request e. We only dispatch items to you on Weekday. 3Repair Some items might be broken caused by improper use, we are always happy to offer any helpful repair service. My package was damaged in transit, who do I contact? We take great care in packaging your order, however damage may occur occasionally while in transit. The item "Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner" is in sale since Thursday, October 25, 2018. This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Transceivers". The seller is "shuangtai-elec" and is located in Shenzhen. This item can be shipped worldwide.
  • Output power: 5W (Standard, DC 13.8V) , 15W (Full,DC 13.8V)
  • Supported Modes: AM, CW, FM, SSB
  • TX: 0.5-30MHz
  • Band Plan: 0
  • Dimensions: 190mm*69mm*45mm
  • Functions: Multiple Working Mode
  • MPN: Does Not Apply
  • Band: AM
  • Bundle Listing: Yes
  • Weight: 623g
  • Brand: Unbranded
  • Mono/Multi Band: Mono Band
  • Type: Mobile/In-Vehicle
  • Frequency Range – RX: 1.8-30MHz
  • Frequency Band(s): 0.5-30MHz
  • Model: RS-918
  • Features: Channel monitor
  • Country/Region of Manufacture: China
  • RX: All HAM HF BANDS

Recent 15W RS-918SSB HF SDR HAM Transceiver Transmit TX 0.5-30MHz Power Scaner

More from recent