Ham Radio Transceiver

Ham Radio Transceiver » rs-928 https://hamradiotransceiver.biz Sat, 20 Jun 2026 17:42:48 +0000 en-CA hourly 1 https://wordpress.org/?v=4.1.1 10-15W RS-928 SSB HF SDR HAM Transceiver Transmit Power TX 0.5-30MHz + Battery https://hamradiotransceiver.biz/2024/12/10-15w-rs-928-ssb-hf-sdr-ham-transceiver-transmit-power-tx-0-5-30mhz-battery/ https://hamradiotransceiver.biz/2024/12/10-15w-rs-928-ssb-hf-sdr-ham-transceiver-transmit-power-tx-0-5-30mhz-battery/#comments Mon, 02 Dec 2024 20:09:55 +0000 https://hamradiotransceiver.biz/2024/12/10-15w-rs-928-ssb-hf-sdr-ham-transceiver-transmit-power-tx-0-5-30mhz-battery/ read more]]>
10-15W RS-928 SSB HF SDR HAM Transceiver Transmit Power TX 0.5-30MHz + Battery

10-15W RS-928 SSB HF SDR HAM Transceiver Transmit Power TX 0.5-30MHz + Battery

HF QRP Transceiver, put battery 12v and ANT can qso. DC IN:9-13V Max:3A. Transmit: 160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive: 3.5-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. Bandwidth:300Hz-10Khz Adj. SWR:Display 1-5. Better than -108 dBm (0.89uV) in a 2.3 kHz bandwidth. Better than -120 dBm (0.22uV) in a 300 Hz bandwidth. Enclosure Design: Removable. Stm32f407VGT6 1M memory. Because this is a software-defined radio and due to ongoing modifications/improvements of the software and hardware, the specifications continue to improve. Receiver sensitivity for 10dB S/N, CCITT filtering, taken at 28.3 MHz. Better than -111 dBm (0.6uV) in a 2.3 kHz bandwidth. Better than -126 dBm (0.11uV) in a 300 Hz bandwidth. The above specifications are for a receiver on which the published sensitivity modifications are performed. Transmit:160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive:3.5-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. Note:The ability of the Si570 to tune the radio below 2.5 MHz is not guaranteed in its specifications, but most units have enough range to tune just below 1.8 Mhz. Maybe there are some small gaps where LO does not work-if it works, it works fine. Indicator is the color of. White: fully working. Yellow: mostly working, maybe there are some small gaps. Red: not working. Spectrum Scope:This is a spectrum analyzer with the vertical divisions representing userdefinable amplitude variations of 5,7.5,10, 15,20,1 S-Unit (6dB), 2 S-Units (12dB) or 3 S-Units. The baseline (“reference level”) of the analyzer is automatically adjusted so that the signals within the displayed passband best fit the dynamic range selected by the userselected dB/division. A graticule along the bottom of the display indicates the approximate frequency of the signal being displayed over a width of +/- 24 kHz. Waterfall Display:As with the spectrum scope, the frequency is displayed along the “x” axis but the signal strength is implied by the displayed color. The newest signals are displayed along the bottom of the screen, but as new readings arrive, the representations of the older signals are shifted upwards giving an ephemeral time record of recent activity on nearby frequencies. There are several options for color “palettes” that range from simple grayscale to “cold-hot” to “rainbow” to represent weak to strong signals. There is also a “Magnify” modefor both the Spectrum Scope and Waterfall Display mode that provides 2x magnification, reducing the visible spectral width to just +/- 12 kHz 24 kHz total. Both the Spectrum Scope and Waterfall Display are very highly configurable. It is possible to disable one or both spectral display modes if desired. Frequency stability:+/- 30 Hz at 14 MHz over the range of 10 to 35 C, ambient with the transceiver in the case or better with the TCXO active. It can be much better than this. FM options:Carrier (ultrasonic) squelch, subaudible tone encoding and decoding, tone burst (“whistle up”) generation, “narrow” (+/-2.5 kHz) and “wide” (+/-5 kHz) deviation and the selection of 7.2,10,12 or 15 kHz pre-detection receive bandwidths. FM sensitivity for 12 dB SINAD, CCITT filtering. 7.2 kHz BW filter: -103.7 dBm (1.46uV) with 1 kHz tone at +/-1.5 kHz. 10 kHz BW filter: -102.1 dBm (1.75uV) with 1 kHz tone at +/-1.5 kHz. 10 kHz BW filter: -104.0 dBm (1.41uV) with 1 kHz tone at +/- 3kHz. 12 kHz BW filter: -102.7 dBm (1.63uV) with 1 kHz tone at +/- 3kHz. 15 kHz BW filter: -99dBm dBm (2.50uV) with 1 kHz tone at +/- 3 kHz. CW mode receive/transmit and frequency display details:Nine modes of CW display/shifting are available to emulate the various makes of radios and suit the user’s taste, ranging from no shifting, display-only shifting, display and LO shifting and manual or automatic LSB/USB shifting. In CW mode “CW-L” or “CW-U”, is displayed depending on whether LSB or USB is being used for reception. CW Speed range: 5-48 WPM. Available audio filter bandwidths in this firmware version:300 Hz, 500 Hz, 1.8 kHz, 2.3 kHz, 3.6 kHz, with a “wide” filter of 5,6,7.5 or 10 kHz being selectable in all modes except FM, where the filtering is done prior to demodulation as noted above. All filters are softwaredefined and additional bandwidths could be made available. Filters can be used as BPF or as LPF selectable in main menu. DSP Filtering Capability:Noise reduction and Automatic Notch Filter with adjustable parameters. Notch filtering is disabled in CW mode for (obvious reasons) or when using a “wide” receive bandwidth. Devel-branch: Because NR activation leads to instability of mcHF it is disabled by default. If you want to use it (and risk instabilities in various scenarios) you can activate NR in config menu “last item”. Setting will NOT BE STORED and must be activated after every powering on. When NR issues are fixed and NR will be improved this function will be obsolete. S-Meter calibration:”Industry Standard”IARU Region 1, Technical recommendation R. Units above S-9 are in dB units, as noted. External audio input/output connections. “Line In” and “Line Out” audio ports, and a “PTT”(Push-to-Talk) are provided via 3.5mm connectors to allow the connection to an external device. (devel-branch only):There is CAT function and audio-in and out also as IQ in and out via USB available. Setting of input is in main menu #60 or via long-press of M3. Line out signal levels:Nominal 1 volt peak-peak, maximum when AGC is operating. Line in signal levels:Nominal 0.1-1.0 volt peak-peak, adjustable using the “Line Input Gain” settings. Transmit ALC type:Look-ahead gain compressor with both pre-set and available “custom” settings. 16.0 volts maximum (when capacitors C27 and tantalum parallel to C106 both rf board are 25V). To 11.0 volts minimum for full transmit power. To 9.5 volts for reduced transmit power. 410mA on 40 meters and below at 13.0 volts, approx. 440 mA on 10 meters, minimum volume, maximum display brightness. The selection of minimum display brightness can reduce this by 40-60mA. Transmit(At 13.0 volts power supply):at full power around 3A;at 10W around 2.5A. United States About 7-14 business time About 5-8 business time. Canada/Australia About 8-15 business time About 5-8 business time. Asia About 15-20 business time About 5-8 business time. Most of the European About 12-20 business time About 5-10 business time. Most of the European Union About 10-15 business time About 5-8 business time. South America About 25-37 business time About 6-11 business time. We are founded in 2010, is a professional purchasing B2B & B2C tool in. We will reply you in 24 hours and give your a satified answer.
10-15W RS-928 SSB HF SDR HAM Transceiver Transmit Power TX 0.5-30MHz + Battery

]]> https://hamradiotransceiver.biz/2024/12/10-15w-rs-928-ssb-hf-sdr-ham-transceiver-transmit-power-tx-0-5-30mhz-battery/feed/ 0 Built-in Battery RS-928 RTC 1-30MHz HF QRP Transceiver SDR CWithLSB/USB/AM/FM https://hamradiotransceiver.biz/2020/03/built-in-battery-rs-928-rtc-1-30mhz-hf-qrp-transceiver-sdr-cwithlsbusbamfm/ https://hamradiotransceiver.biz/2020/03/built-in-battery-rs-928-rtc-1-30mhz-hf-qrp-transceiver-sdr-cwithlsbusbamfm/#comments Tue, 10 Mar 2020 17:24:08 +0000 http://hamradiotransceiver.biz/2020/03/built-in-battery-rs-928-rtc-1-30mhz-hf-qrp-transceiver-sdr-cwithlsbusbamfm/ read more]]>

Built-in Battery RS-928 RTC 1-30MHz HF QRP Transceiver SDR CWithLSB/USB/AM/FM

New verison Built-in battery RS-928 It is stm32f407VGT6 1M memory Battery is 3x 18650 2200mah Output POWER. Please contact me before you return it. If item is defective after 3 months, you can still send it back to us. We will send you a new one after receiving the defective item. If you do not receive our reply, please kindly re-sent your message and we will reply to you as soon as possible. If you have any problems or concerns whatever with your order or products, please message us and give us a chance to assist you before you leave any feedback. We believe we can produce a positive outcome to any situation and will work hard to earn your praise. Our office hours are 9:00 a. M to 6:00 p. M (GMT +8) of Monday to Saturday. And our Office is closed on Sunday and public holidays. We apologize for the late reply during the holidays. The item “Built-in Battery RS-928 RTC 1-30MHz HF QRP Transceiver SDR CWithLSB/USB/AM/FM” is in sale since Wednesday, September 5, 2018. This item is in the category “Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Transceivers”. The seller is “pincei” and is located in Shenzhen. This item can be shipped worldwide.

Band: HF
Supported Modes: AM
MPN: Does Not Apply
Brand: Unbranded

]]> https://hamradiotransceiver.biz/2020/03/built-in-battery-rs-928-rtc-1-30mhz-hf-qrp-transceiver-sdr-cwithlsbusbamfm/feed/ 0 Built-in Battery RS-928 RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver TOP https://hamradiotransceiver.biz/2019/04/built-in-battery-rs-928-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-top/ https://hamradiotransceiver.biz/2019/04/built-in-battery-rs-928-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-top/#comments Sun, 21 Apr 2019 09:06:27 +0000 http://hamradiotransceiver.biz/2019/04/built-in-battery-rs-928-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-top/ read more]]>

Built-in Battery RS-928 RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver TOP

Built-in Battery RS-928 RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver TOP SZ. New verison Built-in battery RS-928 It is stm32f407VGT6 1M memory Battery is 3x 18650 2200mah Output POWER: <=10W Transmit: 160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive: 1-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. Receiver sensitivity for 10dB S/N, CCITT filtering, taken at 28.3 MHz: Frequency Translation enabled: - Better than -111 dBm (0.6uV) in a 2.3 kHz bandwidth - Better than -126 dBm (0.11uV) in a 300 Hz bandwidth - Frequency Translation Disabled: - Better than -108 dBm (0.89uV) in a 2.3 kHz bandwidth - Better than -120 dBm (0.22uV) in a 300 Hz bandwidth - The above specifications are for a receiver on which the published sensitivity modifications are performed. Enclosure Design: Removable - Built-in MIC, PTT - Battery Removable, easy access for replacement Frequency coverage: - Transmit: 160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive: 1-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. Note that the ability of the Si570 to tune the radio below 2.5 MHz is not guaranteed in its specifications, but most units have enough range to tune just below 1.8 Mhz. Maybe there are some small gaps where LO does not work- if it works, it works fine. Indicator is the color of the frequency digits: White: fully working Yellow: mostly working, maybe there are some small gaps Red: not working Spectral Display Modes: - Spectrum Scope: This is a spectrum analyzer with the vertical divisions representing userdefinable amplitude variations of 5,7.5,10,15, 20,1 S-Unit (6dB), 2 S-Units (12dB) or 3 S-Units. The baseline ("reference level") of the analyzer is automatically adjusted so that the signals within the displayed passband best-fit the dynamic range selected by the userselected dB/division. A graticule along the bottom of the display indicates the approximate frequency of the signal being displayed over a width of +/- 24 kHz. Waterfall Display: As with the spectrum scope, the frequency is displayed along the "x" axis but the signal strength is implied by the displayed color. The newest signals are displayed along the bottom of the screen, but as new readings arrive, the representations of the older signals are shifted upwards giving an ephemeral time record of recent activity on nearby frequencies. There are several options for color "palettes" that range from simple grayscale to "cold-hot" to "rainbow" to represent weak to strong signals. There is also a "Magnify" mode for both the Spectrum Scope and Waterfall Display mode that provides 2x magnification, reducing the visible spectral width to just +/- 12 kHz 24 kHz total. Transmitter power output: <=10 Watts, typical, linear. Modifications may be made to increase this: Follow the discussions in the Yahoo group. Frequency stability: +/- 30 Hz at 14 MHz over the range of 10 to 35 C, ambient with the transceiver in the case or better with the TCXO active. It can be much better than this. FM sensitivity for 12 dB SINAD, CCITT filtering: 7.2 kHz BW filter: -103.7 dBm (1.46uV) with 1 kHz tone at +/-1.5 kHz 10 kHz BW filter: -102.1 dBm (1.75uV) with 1 kHz tone at +/-1.5 kHz 10 kHz BW filter: -104.0 dBm (1.41uV) with 1 kHz tone at +/- 3kHz 12 kHz BW filter: -102.7 dBm (1.63uV) with 1 kHz tone at +/- 3kHz 15 kHz BW filter: -99dBm dBm (2.50uV) with 1 kHz tone at +/- 3 kHz CW mode receive/transmit and frequency display details: Nine modes of CW display/shifting are available to emulate the various makes of radios and suit the user's taste, ranging from no shifting, display-only shifting, display and LO shifting and manual or automatic LSB/USB shifting. In CW mode "CW-L" or "CW-U" , is displayed depending on whether LSB or USB is being used for reception. CW Speed range: 5-48 WPM. Available audio filter bandwidths in this firmware version: 300 Hz, 500 Hz, 1.8 kHz, 2.3 kHz, 3.6 kHz, with a "wide" filter of 5,6,7.5 or 10 kHz being selectable in all modes except FM, where the filtering is done prior to demodulation as noted above. All filters are softwaredefined and additional bandwidths could be made available. Filters can be used as BPF or as LPF selectable in main menu. DSP Filtering Capability: Noise reduction and Automatic Notch Filter with adjustable parameters. Notch filtering is disabled in CW mode for (obvious reasons) or when using a "wide" receive bandwidth. Devel-branch: Because NR activation leads to instability of mcHF it is disabled by default. If you want to use it (and risk instabilities in various scenarios) you can activate NR in config menu "last item". Setting will NOT BE STORED and must be activated after every powering on. When NR issues are fixed and NR will be improved this function will be obsolete. S-Meter calibration: - "Industry Standard" IARU Region 1, Technical recommendation R. Units above S-9 are in dB units, as noted. External audio input/output connections: - " Line In" and "Line Out" audio ports, and a "PTT" (Push-to-Talk) are provided via 3.5mm connectors to allow the connection to an external device. (devel-branch only): There is CAT function and audio-in and out also as IQ in and out via USB available. Setting of input is in main menu #60 or via long-press of M3. Line out signal levels: Nominal 1 volt peak-peak, maximum when AGC is operating. Line in signal levels: Nominal 0.1-1.0 volt peak-peak, adjustable using the "Line Input Gain" settings. Transmit ALC type: Look-ahead gain compressor with both pre-set and available "custom" settings. 410mA on 40 meters and below at 13.0 volts, approx. 440 mA on 10 meters, minimum volume, maximum display brightness. The selection of minimum display brightness can reduce this by 40-60mA. The modification to the PA drivers to switch off bias when not in TX mode can reduce this by a further 30-60 mA. Power off: - <5 mA if the PA driver bias modification is performed. If this modification is not performed it is recommended that power be disconnected from the transceiver as the PA driver transistors will be biased on even when the power is turned off, causing 30-60 mA of standing current. With modification RF-04-:-010 from German mcHF Project Group consumption in power off is <0.5uA. Transmit (At 13.0 volts power supply):at full power around 3A;at 10W around 2.5A. Usually it cost about 35USD-50USD. Thanks for your understanding. If you receive defective item, please kindly notify us within 14 days. The item "Built-in Battery RS-928 RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver TOP" is in sale since Wednesday, September 5, 2018. This item is in the category "Mobile Phones & Communication\Radio Communication Equipment\Ham/Amateur Radio\Ham Radio Transceivers". The seller is "topskyrc" and is located in Shenzhen. This item can be shipped worldwide.

Model: RS-928
MPN: Does Not Apply
Brand: Unbranded
Supported Modes: AM
Country/Region of Manufacture: China
Band: HF

]]> https://hamradiotransceiver.biz/2019/04/built-in-battery-rs-928-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-top/feed/ 0 RS-928 PLUS RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in battery https://hamradiotransceiver.biz/2018/12/rs-928-plus-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-battery/ https://hamradiotransceiver.biz/2018/12/rs-928-plus-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-battery/#comments Mon, 17 Dec 2018 07:27:36 +0000 http://hamradiotransceiver.biz/2018/12/rs-928-plus-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-battery/ read more]]>

RS-928 PLUS RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in battery

12.6V 2.2AH Battery inside Rechargeable. Spectrum Dynamic Waterfall Display. Multiple Working Modes: Receive Mode, Transmit Mode, TUNE Mode, VFO Mode, SPLIT Mode. DSP Digital Signal Processing Noise Reduction. Humanized Interface Color Display. Receive Fine Tuning Function, Changeable MIC Gain Value. VCC Power Supply Voltage Indication Table. Transmit Signal Strength Display Table. Multifunctional Instrument: SWR Standing Wave Ratio Meter, AVD Audio Frequency Meter, ALC Signal Modulation Meter. Build in USB Sound Card support WSJT-X use FT-817 Rig. Acc Jack Port Support 70-100W HF Pa Amp T/R. V0.6 pcb redesign upgrade many hardware mod. Inside MIC and PTT (Press TUNE). TX: All HAM HF Bands. SSB(J3E)CWAM(RX Only), FM, FREE-DV, SAM, RTTY. 5W (Standard, Battery) , 10W (Full, DC 13.8V)28M Max <=5W. 0.110.89V(RFC 50-20). 18650x3 12.6V 2200mah. Battery Low power off. 8.8V (SET in MENU). ±1.5PPM (27M TCXO). Product Dimension (W × H × D). Transceiver comes with automatic key generator circuit. Can be connected to the use of automatic keys. Each Set Package Contain. 1× BNC To SO239 Convertor. Orders will be processed and dispatched within 3 days normally. Our listing price includes the value of goods, packaging cost, and export. Please check with your country's. We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails. Our aim is to provide Top Level Customer Service, your recognition will encourage us greatly and serve you better. We strive to keep all our customers satisfy. We will always do our up most to exceed your expectations in customer service, communication and dispatching of your orders. The item "RS-928 PLUS RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in battery" is in sale since Saturday, August 11, 2018. This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Transceivers". The seller is "chunyu1991_1" and is located in GUANG DONG. This item can be shipped worldwide.

Model: R928
Modified Item: No
Custom Bundle: No
MPN: Does Not Apply
Brand: Unbranded
Non-Domestic Product: No

]]> https://hamradiotransceiver.biz/2018/12/rs-928-plus-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-battery/feed/ 0 RS-928 PLUS RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in batter T https://hamradiotransceiver.biz/2018/09/rs-928-plus-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-batter-t/ https://hamradiotransceiver.biz/2018/09/rs-928-plus-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-batter-t/#comments Sat, 29 Sep 2018 23:52:24 +0000 http://hamradiotransceiver.biz/2018/09/rs-928-plus-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-batter-t/ read more]]>

RS-928 PLUS RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in batter T

RS-928 PLUS RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in batter. New verison Built-in battery RS-928 It is stm32f407VGT6 1M memory Battery is 3x 18650 2200mah Output POWER: <=10W Transmit: 160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive: 1-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. Receiver sensitivity for 10dB S/N, CCITT filtering, taken at 28.3 MHz: Frequency Translation enabled: - Better than -111 dBm (0.6uV) in a 2.3 kHz bandwidth - Better than -126 dBm (0.11uV) in a 300 Hz bandwidth - Frequency Translation Disabled: - Better than -108 dBm (0.89uV) in a 2.3 kHz bandwidth - Better than -120 dBm (0.22uV) in a 300 Hz bandwidth - The above specifications are for a receiver on which the published sensitivity modifications are performed. Enclosure Design: Removable - Built-in MIC, PTT - Battery Removable, easy access for replacement Frequency coverage: - Transmit: 160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive: 1-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. Note that the ability of the Si570 to tune the radio below 2.5 MHz is not guaranteed in its specifications, but most units have enough range to tune just below 1.8 Mhz. Maybe there are some small gaps where LO does not work- if it works, it works fine. Indicator is the color of the frequency digits: White: fully working Yellow: mostly working, maybe there are some small gaps Red: not working Spectral Display Modes: - Spectrum Scope: This is a spectrum analyzer with the vertical divisions representing userdefinable amplitude variations of 5,7.5,10,15, 20,1 S-Unit (6dB), 2 S-Units (12dB) or 3 S-Units. The baseline ("reference level") of the analyzer is automatically adjusted so that the signals within the displayed passband best-fit the dynamic range selected by the userselected dB/division. A graticule along the bottom of the display indicates the approximate frequency of the signal being displayed over a width of +/- 24 kHz. Waterfall Display: As with the spectrum scope, the frequency is displayed along the "x" axis but the signal strength is implied by the displayed color. The newest signals are displayed along the bottom of the screen, but as new readings arrive, the representations of the older signals are shifted upwards giving an ephemeral time record of recent activity on nearby frequencies. There are several options for color "palettes" that range from simple grayscale to "cold-hot" to "rainbow" to represent weak to strong signals. There is also a "Magnify" mode for both the Spectrum Scope and Waterfall Display mode that provides 2x magnification, reducing the visible spectral width to just +/- 12 kHz 24 kHz total. Transmitter power output: <=10 Watts, typical, linear. Modifications may be made to increase this: Follow the discussions in the Yahoo group. Frequency stability: +/- 30 Hz at 14 MHz over the range of 10 to 35 C, ambient with the transceiver in the case or better with the TCXO active. It can be much better than this. FM sensitivity for 12 dB SINAD, CCITT filtering: 7.2 kHz BW filter: -103.7 dBm (1.46uV) with 1 kHz tone at +/-1.5 kHz 10 kHz BW filter: -102.1 dBm (1.75uV) with 1 kHz tone at +/-1.5 kHz 10 kHz BW filter: -104.0 dBm (1.41uV) with 1 kHz tone at +/- 3kHz 12 kHz BW filter: -102.7 dBm (1.63uV) with 1 kHz tone at +/- 3kHz 15 kHz BW filter: -99dBm dBm (2.50uV) with 1 kHz tone at +/- 3 kHz CW mode receive/transmit and frequency display details: Nine modes of CW display/shifting are available to emulate the various makes of radios and suit the user's taste, ranging from no shifting, display-only shifting, display and LO shifting and manual or automatic LSB/USB shifting. In CW mode "CW-L" or "CW-U" , is displayed depending on whether LSB or USB is being used for reception. CW Speed range: 5-48 WPM. Available audio filter bandwidths in this firmware version: 300 Hz, 500 Hz, 1.8 kHz, 2.3 kHz, 3.6 kHz, with a "wide" filter of 5,6,7.5 or 10 kHz being selectable in all modes except FM, where the filtering is done prior to demodulation as noted above. All filters are softwaredefined and additional bandwidths could be made available. Filters can be used as BPF or as LPF selectable in main menu. DSP Filtering Capability: Noise reduction and Automatic Notch Filter with adjustable parameters. Notch filtering is disabled in CW mode for (obvious reasons) or when using a "wide" receive bandwidth. Devel-branch: Because NR activation leads to instability of mcHF it is disabled by default. If you want to use it (and risk instabilities in various scenarios) you can activate NR in config menu "last item". Setting will NOT BE STORED and must be activated after every powering on. When NR issues are fixed and NR will be improved this function will be obsolete. S-Meter calibration: - "Industry Standard" IARU Region 1, Technical recommendation R. Units above S-9 are in dB units, as noted. External audio input/output connections: - " Line In" and "Line Out" audio ports, and a "PTT" (Push-to-Talk) are provided via 3.5mm connectors to allow the connection to an external device. (devel-branch only): There is CAT function and audio-in and out also as IQ in and out via USB available. Setting of input is in main menu #60 or via long-press of M3. Line out signal levels: Nominal 1 volt peak-peak, maximum when AGC is operating. Line in signal levels: Nominal 0.1-1.0 volt peak-peak, adjustable using the "Line Input Gain" settings. Transmit ALC type: Look-ahead gain compressor with both pre-set and available "custom" settings. 410mA on 40 meters and below at 13.0 volts, approx. 440 mA on 10 meters, minimum volume, maximum display brightness. The selection of minimum display brightness can reduce this by 40-60mA. The modification to the PA drivers to switch off bias when not in TX mode can reduce this by a further 30-60 mA. Power off: - <5 mA if the PA driver bias modification is performed. If this modification is not performed it is recommended that power be disconnected from the transceiver as the PA driver transistors will be biased on even when the power is turned off, causing 30-60 mA of standing current. With modification RF-04-:-010 from German mcHF Project Group consumption in power off is <0.5uA. Transmit (At 13.0 volts power supply):at full power around 3A;at 10W around 2.5A. Usually it cost about 35USD-50USD. Thanks for your understanding. If you receive defective item, please kindly notify us within 14 days. The item "RS-928 PLUS RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in batter T" is in sale since Friday, June 29, 2018. This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Transceivers". The seller is "topskyrc" and is located in HK. This item can be shipped worldwide.

Frequency Band(s): HF
Model: 829
Country/Region of Manufacture: China
Band: HF
Type: Portable/Handheld
Supported Modes: AM
MPN: Does Not Apply
Brand: Unbranded

Incoming search terms:

rs-928

]]> https://hamradiotransceiver.biz/2018/09/rs-928-plus-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-batter-t/feed/ 0 RS-928 RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in battery https://hamradiotransceiver.biz/2018/01/rs-928-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-battery/ https://hamradiotransceiver.biz/2018/01/rs-928-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-battery/#comments Mon, 29 Jan 2018 15:11:38 +0000 http://hamradiotransceiver.biz/2018/01/rs-928-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-battery/ read more]]>

RS-928 RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in battery

MX-P50M HF Power Amplifier 45W DC13.8V for FT-817 Elecraft KX3 QRP Ham Radio. MAT-180H HF Auto-tuner 120W Automatic Antenna Ham Radio for ICOM. Tuner Short Wave HF 120W Auto Antenna Tuning Magnetic Latching Relay MAT-125E. NEW HF Power Amplifier For YASEU FT-817 ICOM IC-703 Elecraft KX3 QRP Ham Radio. Mini HF Power Amplifier For YASEU FT-817 ICOM IC-703 Elecraft KX3 QRP Ham Radio. New Xiegu X-108G X108G Outdoor VERSION 0.5-30MHz 20W HF TRANSCEIVER QRP SSB-CW. New AW07A 160M HF/VHF/UHF Impedance SWR Antenna Analyzer for Ham Radio Hobbists. 1MHz-700MHZ 3.2W HF VHF UHF FM Transmitter RF Power Amplifier for Ham Radio. RS-928 V6 RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in battery. Recent 10W (15W) RS-928 SSB HF SDR HAM Transceiver Transmit Power TX Scaner. Article New verison Built-in battery RS-928 Output POWER: <=10W(44dbm) Transmit: 160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive: 1-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. Receiver sensitivity for 10dB S/N, CCITT filtering, taken at 28.3 MHz: Frequency Translation enabled: - Better than -111 dBm (0.6uV) in a 2.3 kHz bandwidth - Better than -126 dBm (0.11uV) in a 300 Hz bandwidth - Frequency Translation Disabled: - Better than -108 dBm (0.89uV) in a 2.3 kHz bandwidth - Better than -120 dBm (0.22uV) in a 300 Hz bandwidth - The above specifications are for a receiver on which the published sensitivity modifications are performed. Frequency coverage: - Transmit: 160,80,60,40,30,20,17,15,12 and 10 meter amateur bands. Receive: 1-30 MHz nominal including general coverage, 0.8-32 MHz at reduced specifications. Note that the ability of the Si570 to tune the radio below 2.5 MHz is not guaranteed in its specifications, but most units have enough range to tune just below 1.8 Mhz. Maybe there are some small gaps where LO does not work- if it works, it works fine. Indicator is the color of the frequency digits: White: fully working Yellow: mostly working, maybe there are some small gaps Red: not working Spectral Display Modes: - Spectrum Scope: This is a spectrum analyzer with the vertical divisions representing userdefinable amplitude variations of 5,7.5,10,15, 20,1 S-Unit (6dB), 2 S-Units (12dB) or 3 S-Units. The baseline ("reference level") of the analyzer is automatically adjusted so that the signals within the displayed passband best-fit the dynamic range selected by the userselected dB/division. A graticule along the bottom of the display indicates the approximate frequency of the signal being displayed over a width of +/- 24 kHz. Waterfall Display: As with the spectrum scope, the frequency is displayed along the "x" axis but the signal strength is implied by the displayed color. The newest signals are displayed along the bottom of the screen, but as new readings arrive, the representations of the older signals are shifted upwards giving an ephemeral time record of recent activity on nearby frequencies. There are several options for color "palettes" that range from simple grayscale to "cold-hot" to "rainbow" to represent weak to strong signals. There is also a "Magnify" mode for both the Spectrum Scope and Waterfall Display mode that provides 2x magnification, reducing the visible spectral width to just +/- 12 kHz 24 kHz total. Transmitter power output: <=10 Watts, typical, linear. Modifications may be made to increase this: Follow the discussions in the Yahoo group. Frequency stability: +/- 30 Hz at 14 MHz over the range of 10 to 35 C, ambient with the transceiver in the case or better with the TCXO active. It can be much better than this. FM sensitivity for 12 dB SINAD, CCITT filtering: 7.2 kHz BW filter: -103.7 dBm (1.46uV) with 1 kHz tone at +/-1.5 kHz 10 kHz BW filter: -102.1 dBm (1.75uV) with 1 kHz tone at +/-1.5 kHz 10 kHz BW filter: -104.0 dBm (1.41uV) with 1 kHz tone at +/- 3kHz 12 kHz BW filter: -102.7 dBm (1.63uV) with 1 kHz tone at +/- 3kHz 15 kHz BW filter: -99dBm dBm (2.50uV) with 1 kHz tone at +/- 3 kHz CW mode receive/transmit and frequency display details: Nine modes of CW display/shifting are available to emulate the various makes of radios and suit the user's taste, ranging from no shifting, display-only shifting, display and LO shifting and manual or automatic LSB/USB shifting. In CW mode "CW-L" or "CW-U" , is displayed depending on whether LSB or USB is being used for reception. CW Speed range: 5-48 WPM. Available audio filter bandwidths in this firmware version: 300 Hz, 500 Hz, 1.8 kHz, 2.3 kHz, 3.6 kHz, with a "wide" filter of 5,6,7.5 or 10 kHz being selectable in all modes except FM, where the filtering is done prior to demodulation as noted above. All filters are softwaredefined and additional bandwidths could be made available. Filters can be used as BPF or as LPF selectable in main menu. DSP Filtering Capability: Noise reduction and Automatic Notch Filter with adjustable parameters. Notch filtering is disabled in CW mode for (obvious reasons) or when using a "wide" receive bandwidth. Devel-branch: Because NR activation leads to instability of mcHF it is disabled by default. If you want to use it (and risk instabilities in various scenarios) you can activate NR in config menu "last item". Setting will NOT BE STORED and must be activated after every powering on. When NR issues are fixed and NR will be improved this function will be obsolete. S-Meter calibration: - "Industry Standard" IARU Region 1, Technical recommendation R. Units above S-9 are in dB units, as noted. External audio input/output connections: - " Line In" and "Line Out" audio ports, and a "PTT" (Push-to-Talk) are provided via 3.5mm connectors to allow the connection to an external device. (devel-branch only): There is CAT function and audio-in and out also as IQ in and out via USB available. Setting of input is in main menu #60 or via long-press of M3. Line out signal levels: Nominal 1 volt peak-peak, maximum when AGC is operating. Line in signal levels: Nominal 0.1-1.0 volt peak-peak, adjustable using the "Line Input Gain" settings. Transmit ALC type: Look-ahead gain compressor with both pre-set and available "custom" settings. 410mA on 40 meters and below at 13.0 volts, approx. 440 mA on 10 meters, minimum volume, maximum display brightness. The selection of minimum display brightness can reduce this by 40-60mA. The modification to the PA drivers to switch off bias when not in TX mode can reduce this by a further 30-60 mA. Power off: - <5 mA if the PA driver bias modification is performed. If this modification is not performed it is recommended that power be disconnected from the transceiver as the PA driver transistors will be biased on even when the power is turned off, causing 30-60 mA of standing current. With modification RF-04-:-010 from German mcHF Project Group consumption in power off is <0.5uA. Transmit (At 13.0 volts power supply):at full power around 3A;at 10W around 2.5A. International buyers please note: a. These charges are buyers responsibility. The item "RS-928 RTC 10W 1-30MHz HF QRP Transceiver SDR Transceiver Built-in battery" is in sale since Thursday, January 11, 2018. This item is in the category "Consumer Electronics\Radio Communication\Ham, Amateur Radio\Ham Radio Transceivers". The seller is "cybereveryday" and is located in HK. This item can be shipped worldwide.

Frequency Band(s): HF
Brand: Unbranded/Generic
MPN: Does Not Apply

]]> https://hamradiotransceiver.biz/2018/01/rs-928-rtc-10w-1-30mhz-hf-qrp-transceiver-sdr-transceiver-built-in-battery/feed/ 0 Recent 10W (15W) RS-928 SSB HF SDR HAM Transceiver Transmit Power TX Scaner https://hamradiotransceiver.biz/2018/01/recent-10w-15w-rs-928-ssb-hf-sdr-ham-transceiver-transmit-power-tx-scaner/ https://hamradiotransceiver.biz/2018/01/recent-10w-15w-rs-928-ssb-hf-sdr-ham-transceiver-transmit-power-tx-scaner/#comments Wed, 17 Jan 2018 02:26:20 +0000 http://hamradiotransceiver.biz/2018/01/recent-10w-15w-rs-928-ssb-hf-sdr-ham-transceiver-transmit-power-tx-scaner/ read more]]>

Recent 10W (15W) RS-928 SSB HF SDR HAM Transceiver Transmit Power TX Scaner

Frequency Band(s): HF
Supported Modes: SSB
Brand: Unbranded/Generic
MPN: Does Not Apply
Frequency Range: TX: 0.5MHz-30MHz ; RX: All HAM HF Bands
TX Power: 5W (Standard, DC 13.8V),15W (Full,DC 13.8V)
Receiving Sensitivity: 0.11~0.89V(RFC 50-20)
Minimum Frequency Step: 1Hz
Operating Voltage: DC9~15V
Dimension: 190x69x45mm

]]> https://hamradiotransceiver.biz/2018/01/recent-10w-15w-rs-928-ssb-hf-sdr-ham-transceiver-transmit-power-tx-scaner/feed/ 0